Making Computer Cases out of Plexiglass? 30
antis0c asks: "After reading many stories on Slashdot about building custom PC cases, I'm highly interested in building one myself. The only problem - I have absolutely no experience working with PlexiGlass/Acrylic/Lexan, basically any plastic type materials. I'd like to learn the basics, cutting, adhesives, special tools, all the skills required to build a PC case out of this stuff. A quick Google search left nothing really good on it, and I can't even find any books on Amazon on the topic. I hoping some Slashdotters might have some insight on good books on the topic, sites, or perhaps just information."
Cutting, gluing, bending (Score:4, Informative)
There is a special glue, again available at good hardware stores, that basically melts the two pieces of plastic and welds them together. When done properly, it makes a watertight seal. The trick is being very neat about not getting this stuff where you don't want it. Otherwise you'll see it forever.
The trickiest part of working with Plexiglas is bending it. Tools are available which are really nothing more than a long, straight heating element. You put the part of the Plexiglas you want to bend over the heating element for just a few seconds, then you remove it and bend it. You can repeat this a few times, working a bit at a time if need be. It helps if you have a good, square edge on your workbench to make nice 90 degree angles.
Re:Cutting, gluing, bending (Score:2, Informative)
To prevent any scratches, scuffs, and glue spots.. (Score:5, Informative)
Any saw, power or hand saw will cut through the stuff. Drills make easy work of the plexiglass. Epoxy is the best bet for an adhesive, although some will prefer the look of bolted or bracketed corners. Even if you do use bolts and brackets, then still use epoxy, since the bolts/brackets will loosen over time and epoxy won't.
Be carefull of which chemicals you use to clean the plexiglass with. I forgot which ones damage the plastic, but some of them do.
A nice touch is to cut a shape or letters as a hole out of paper or aluminum foil. Tape the aluminum foil to the plexiglass (with contact paper removed) and sand away the plexiglass with some steel wool or sandpaper. This will create a frosted shape of whatever you cut out on the plexiglass. Practice this a few times on a spare piece, but I've seen the results and it looks professional and nice.
Remember, that with plexiglass, the looks of the internals of your PC will be as important as the looks of the case. SPend a little time replacing LED's with blue LED's. Try putting some reflectors near the internal LCDs so that the light reflects around the insides. Buy a few LED's just to hook up to the powersupply that don't do anything. One nice effect is to have all of the LEDs hidden from view, but the light that they create will cause the innerds of the computer to glow.
Bundle wires together.
Remove RF shielding wherever possible (unless you think it will cause 747s to crash in your backyard). If you want an overall RF shield when you are done, then use window screen materials and attach it to the inside or outside of the plexiglass case.
I would appreciate and other ideas or comments/suggestions on these ideas since I am planning to make one too.
Re:To prevent any scratches, scuffs, and glue spot (Score:4, Informative)
Heat and Discoloration: You don't want your case to look like the back window of an old rag top convertable, either vent well or choose a grade of plastic that kind stand higher temps for the MB Backing. Also a big fan with the lights attached to the fins will look cool
Safety: EYES, Lungs, and Skin when ever your cutting plastics or metal with power tools wear a heavy long sleeve shirt, working gloves, eye protection to avoid spinters. (a plastic spinter in your eyes is bad news) Also if you use a power sander or rotory tool wear a dust mask.
ArsTechnica!!!!! (Score:1)
There's tons of extremely knowledgable folks there who'd *LOVE* to help you out.
tips for working plexiglass (Score:5, Informative)
it's fast and dirty to throw some aquarium epoxy on mating edges and call it a day, but a single seamless piece will really stand out in a sea of imitations.
Buy yourself up a good heat gun (sometimes refered to as a paint-stripping gun), a blowtorch with a removeable fishtail spreader, and some good sturdy sheet steel to use as a working surface when playing with fire.
note: a medium-level blowtorch flame will alow you to 'flame-polish' the edges of your plexi creation. once you get good at this and can do it with one even pass you'll love the results. it's the same concept as you use when flame-polishing glass. The fishtail spreader is good for applying heat to a larger area if you don't have a proper electric heat gun.
Expect to make some pretty gruesome mistakes the first few tries. Start making some basic shapes, 90 degree bends and such, with small chunks of plexi. Once you get decent with that, work up to longer bends (not large radius bends, but wider pieces). A friend of mine swears by making jigs out of lengths of thin steel rod (1/8 - 1/4 dia.) and shaping the plexi over it.
Always work in well ventilated areas and don't rush the process. it's not as difficult as glass-blowing, but it still requires a lot of patience to get even surface temperatures on large expanses of the stuff.
As a 1st real project, I would suggest taking a PC chassis with removeable side and front panels, and create a single piece of plexi that 'wraps' from one side, across the front (use drill bits and a dremel to cut your drive openings) and around the other side. trim off any excess sheet metal from the chassis, and you're all set.
Good luck and keep us posted as far as your results.
fun case mod: Cooler Master ATC 210 (Score:2, Informative)
The goal was to be able to reproduce the various bits of plastic on the case. This included 2 side "rails", and a front door. A quick trip to Tap Plastics [tapplastics.com] pretty much got me started with everything I needed in terms of the plastic itself. I left the store with 18"x18" of colored 1/8" sheet of acrylic,, 18"x18"x1/16" sheet of clear acrylic, and acrylic cement as well as a little advice from one of the folks who work there about certain tools NOT to use.
I found the acrylic machines VERY easily, even with non-plastics tools. the bits were cut to size on an old radial-arm saw (didn't have access to a table saw) with an 80 tooth carbide tipped blade. This worked well enough to get a decent finish on the edges, as long as I was carefull with how the acrylic was pushed through the blade.
the only part of the project that I had my doubts about was the arc at the bottom part of the door which gives access to the USB ports of the front of the case. This actually turned out to be pretty easy with a cardboard template, the dremmel with a cutting bit and the router adaptor. the acrylic took well to the bit and didn't really chip at all.
After the bits were cut to size came the filing... lots of it. I aquired a plasics file and went to work smoothing out the edges. Once the saw marks were worked out, hit it with 320 grit sandpaper to smooth the edge out. The last trick was jewellers rouge and a dremmel too with a pollishing (not buffing!) wheel at low speed.
Once all the pieces were polished to a nice shine on the edges came the assembly. This was pretty easy with the help of a little celophane packing tape to hold the pieces together as the cement was applied.
finally, the little aluminum pieces which hold the hinges and magnets for the door were installed with the help of a 3/16" drill bit and the dremmel cutting tool.
the project was a great success and a great learning experience as well. I think the best advice I can give is to just go down to your local plastics shop, pick up some acrylic sheets and play with the machining and assambly. I found the stuff really easy to work with. I now have a one-of-a-kind flourecent-red ATC-210 and my friend has a clear-amber ATC-210.
Bit-tech article on it... (Score:4, Interesting)
"linear" has two articles there so far. "Planning Your Acrylic Case" is seven webpages with details on various aspects of acrylic case design. "The Invisible Case" is sixteen webpages on how the author went about making a (rather ambitious) clear plastic case for their computer (amongst other clear modding), complete with plenty of pictures.
Re:Bit-tech article on it... (Score:2)
I made one (Score:1)
Drew it up on cad, printed the lengths/widths, cut it out with a band saw (some of them on a table saw, however, it can shatter, its good to tape the ends).
drilled holes in
and I never actually used screws..
it fit together to tug, I ended up just keeping a strand of tape on it, until I got my new computer and trashed it
great project, was fun..
EM Radiation? (Score:2, Interesting)
ie the metal case on ur machine acts as a farraday cage, preventing out side EM noise interfering with it, and stop it give of interfering radiation.
now with these plastic cases the cage is broken and thus no longer works.
i beleive there are rules (i duno if law) about the fact ur electrical device most not give of (unreasonable) EM noise, and most with stand EM from other devices (eg in US this set by FCC)
how does plastic cases address these concerns, if at all?
Re:EM Radiation? (Score:2)
I believe (in the States at least) that most consumer grade electronics devices must be certified to produce very little, and to "accept" any dangerous interference (read the FCC/CE declaration that comes with just about anything electronic, e.g., handheld, MP3 player, etc.).
Having said all of that, I don't know that there are any rules that require a home consumer to guarantee that anything they toy around with meets the same rigorous requirements that commercial companies have to follow. Even if there are laws, I doubt that the FCC has the manpower to trawl through neighboorhoods looking for offenders (not to mention that they would likely have to some within about ten feet to get any measurement).
If I had a plexi case, I would just make sure I kept the PC away from the monitor by a couple of feet or so (so you don't get funny colors, and/or data corruption), and you probably would not be able to listen to a radio that is sitting on top of the case due the fields the MoBo would put out.
Some (hopefully local) resources (Score:4, Informative)
2. Your local plastic dealer. It depends on what brand of acrylic they carry, but all the major manufacturers publish little booklets about basic plastic techniques.
Even better, your local plastic dealer will also have tools specifically for plexiglass. It's not that ordinary metal or wood tools won't work; they will, but the cuts won't be as smooth and you're likely to jam on the chips until you learn the basic moves and good feed rates. The tools intended specifically for acrylic plastics are much more forgiving.
Someone else here recommended epoxy adhesives, which are truly a sign of poor workmanship with acrylic. Quality acrylic stuff is bonded by making the gap be very small and using a cement with the consistency of water. Done properly, the joint is optically clear and seamless. It does take some practice.
Some classic websites:
Rohm and Hass make the "plexiglass" brand of acrylic, but I've never found anything useful at their website [rohmhass.com].
Nothing beats a visit to a local plastic dealer, IMHO. Especially if you're looking for lively colors or advice about working the material.
Re:Some (hopefully local) resources (Score:1)
RF Noise (Score:2, Interesting)
Now to you that might be a big deal, but to me it is a big deal.
Ever try operating a Ham Radio in the same room as a computer? It's bad enough with the case on.
One thing you can do is to go buy some fine copper mesh from your local hardware store and put it just underneath the plexiglass, this will capture most/all RF Noise.
Don't Do It (Score:4, Insightful)
How would you like it if every motorist in your neighborhood removed the muffler and pollution controls from their cars, because it looked kewl?
Just a guess (Score:2, Insightful)
How I did it. (Score:2, Informative)
To make bends: propane torch until it gets soft.
We used metal brackets to hold it together, but epoxy also works fine.
Watch for static! (Score:2)
Static electrisity is a big killer of comptuers. Plastic is good at making static electrisity.
I'm not saying you can't do this. I'm not saying it won't be cool. But there is a good chance you will ruin your comptuer sometime when you are trying to modify it. Keep this in mind, and make sure it doesn't happen.
Heat (Score:2, Insightful)
OR just purchase a case (Score:1)
Lexan (Score:1)
It can be cut easily with a handsaw and does not melt due to friction.
It can be bent easily by hanging over a table edge and waving a blowtorch after it.
It is light and strong.
It's a little more expensive than plexiglass I think, but worth it.
Before you buy all the parts (Score:1)
You might find its too hard , then you've wasted your cash.